Number of axes |
3
|
Acceleration Sensor |
MEMS 3-axes
|
Dynamic Range |
+-8 g
|
Bandwidth High Limit |
Adjustable up to 2 kHz (@ 4 kHz Sampling Rate)
|
Bandwidth Low Limit |
DC (High-Pass Filter Bypass), Adjustable from 10 mHz to Fs/2 (High-Pass Filter On)
|
Acceleration Noise X-Y Axes (Typical) |
Note: Acceleration noise is primarily affected by the sampling rate. The higher the sampling rate, the higher the noise., -82 dBg (80 μg RMS) @ 125 Hz Sampling Rate, -66 dBg (500 μg RMS) @ 4 kHz Sampling Rate
|
Acceleration Noise Z Axis (Typical) |
Note: Acceleration noise is primarily affected by the sampling rate. The higher the sampling rate, the higher the noise., -80 dBg (100 μg RMS) @ 125 Hz Sampling Rate, -64 dBg (600 μg RMS) @ 4 kHz Sampling Rate
|
Velocity Noise X-Y Axes (Typical) |
Note: Velocity noise is primarily affected by the high-pass cutoff frequency. The lower the cutoff frequency, the higher the noise., -94 dB-m/s (20 μm/s RMS) @ 1 Hz High-Pass Cutoff, -103 dB-m/s (7 μm/s RMS) @ 10 Hz High-Pass Cutoff
|
Velocity Noise Z Axis (Typical) |
Note: Velocity noise is primarily affected by the high-pass cutoff frequency. The lower the cutoff frequency, the higher the noise., -92 dB-m/s (25 μm/s RMS) @ 1 Hz High-Pass Cutoff, -101 dB-m/s (9 μm/s RMS) @ 10 Hz High-Pass Cutoff
|
Inclination Angle Noise |
Note: Measured using acceleration average, with a log interval of 1s, with the instrument positioned with the Z axis vertical, and X and Y axes horizontal, 1 E − 3°
|
Inclination Angle Temperature Stability |
Note: Measured using acceleration average, with a log interval of 1s, with the instrument positioned with the Z axis vertical, and X and Y axes horizontal, 0.2° over the temperature range -20 °C to 60 °C
|
Connectivity |
USB
|
Measurements |
Raw Acceleration (g or m/s2), Raw Velocity (m/s), Min, Max and Avg Acceleration values (g or m/s2), Min, Max and Avg Velocity values (m/s), Inclinations, Min, Max and Avg RMS Vibration level (linear or dB, g or m/s2), Min, Max and Avg RMS Velocity level (linear or dB, m/s)
|
Duty Rate of Signal Capture |
100% – No Missed Samples
|
Spectral Display |
3-Axes 1024-point Power Spectrum – dB or Lin Scale
|
Modes of Operation |
Idle (Micro-Power), USB-Connected (Active), Recording (Stand-alone), Auto-Rec – Stand-Alone (Idle when no activity / Recording while activity is present)
|
Sampling Clock Accuracy |
1%
|
Date-Time Clock Accuracy |
30ppm
|
Calibration |
Self-Calibration using the earth's gravity as a reference
|
Battery Type |
Integral Li-Poly – USB-Rechargeable
|
Recharge Time |
2 h 30 (Typical)
|
Battery Autonomy (Full-Charge) |
Up to one year while in Idle, 16 days to 125 days while recording, depending on settings
|
Battery Life |
> 300 Charge/Discharge Cycles
|
Temperature Range |
-20°C to 60°C (-4°F to 140°F)
|
Recording Memory |
Non-Volatile Flash Memory
|
Recording Memory Capacity |
128 Mb, (Ex: can continuously record single-axis raw signals for 17 min @ 4 kHz Sampling Rate), (Ex: can continuously record 3-axes full-statistics levels at 1s intervals for 5 days), (Ex: can continuously record 3-axes full statistics levels a 1min intervals for 10 months.)
|
Recording/Erasure Cycles |
Greater than 100 000
|
Data Retention |
Greater than 20 Years
|
Dimensions |
7.62 x 3.94 x 2.06 cm, (3” x 1.55” x 0.81”)
|
Construction |
Integrally Potted Weather-Proof ABS Enclosure
|